Metal Hand Tools

Product Description
18″ Sharp Point Taper Punch. Punch holes in sheet metal for entrance of screws or wires…. More >>

18In Sharp Point Taper Punch

• Package Quantity: (1) 8 Piece Kit
• Tool Type: Portable Hand Punch
• Contents: 3/32; 1/8; 5/32; 3/16; 7/32; 1/4; 9/32 & Hand Punch
• Throat Depth (Inch): 1-3/4
• Fractional Sizes: 3/32; 1/8; 5/32; 3/16; 7/32; 1/4; 9/32

Product Description
Bench Portable Hand And Die Sets – Chisels & Punches Tool Type: Portable Hand Punch Contents: 3/32; 1/8; 5/32; 3/16; 7/32; 1/4; 9/32 & Hand Punch Throat Depth: 1-3/4… More >>

Roper Whitney 135010050 #5 Jr Kit Portable Set Roper Whitney Hand Punch

• Traditional style punch and die set is an economical way to make washers, shims, and gaskets
• Nine punch sizes: 1/8, 3/16, 1/4, 5/16, 3/8, 7/16, 1/2, 5/8, and 3/4″
• Clear plastic top plate is marked with accurate center lines
• Cuts steel, brass, copper, aluminum, rubber, and plastic up to 0.025″ thick
• Cuts stainless steel and blue tempered shim up to 0.010″ thick

Product Description
Punch and Diet set is packaged in a durable plastic case. The base and punches are made of a hardened and ground A-2 tool steel. Mark center lines, align with center lines and hit with hammer…. More >>

Precision Brand Punch and Die Set

• 14 cold chisels and punches made of high-quality drop-forged, heat-treated, high-carbon steel
• Finely finished from their mat-black hex-shafts to polished steel working ends
• Use on cold metal – flatten, indent, groove, reduce thickness, remove trash; cut rods, bars & sheets
• 5 flat cold chisels; 8 round flat-end punches (4 tapered, 4 constant dia.); 1 pointed center punch
• Tough rubberized roll-up pouch keeps them organized, evenly oiled, and dry for stowing and transport

Product Description
Can’t remember the combination to your gun safe? Crack it open with one of these Cold Chisels! But wait, there are more constructive uses for these in working most any hard or soft metal — even composites or wood in some cases. These are named Cold Chisels because they have the strength and configuration to work cold metals. 5 Flat Cold Chisels (blade width x shaft hex measurement x length): 1/2 x 3/ 8 x 6″, 5/8 x 1/2 x 7″, 3/4 x 5/8/ x 7″, 7/8 x 5/8 x 8″, 1 inch x 3/4 x 8″; 4 Tapered Punches (flat tip diameter x shaft hex measurement x length): 1/8 x 3/8 x 8 1/2″, 5/32 x 1/2 x 9″, 1/8 x 1/2 x 10″, 3/8 x 5/8 x 10″; 4 Pin Punches (flat tip diameter x shaft hex measurement x length): 3/32 x 3/8 x 5″, 1/8 x 3/8 x 5″, 3/16 x 3/8 x 6″, 1/4 x 1/2 x 6″; 1 Center Punch (tip diameter x shaft hex measurement x length): 0 x 3/8 x 5″. Flat cold chisels have a less-acute angle to the sharp portion of the blade than woodworking chisels. This gives the cutti… More >>

Cold Chisel & Punch Set – Roll-Up Pouch – 14 Pc

• 5/16″ punch, Performs hole punching and panel crimping, Features a rotating head for convenient us
• Precise control – every pull of the lever delivers a single punch or a single flange crimp
• Forms an offset crimped edge on sheet metals for no-bump lap welds
• Lightweight, yet ruggedly built
• Cuts metal fabrication time in half

Product Description
5/16″ punch, Performs hole punching and panel crimping, Features a rotating head for convenient use, Precise control – every pull of the lever delivers a single punch or a single flange crimp, Forms an offset crimped edge on sheet metals for no-bump lap welds, Lightweight, yet ruggedly built, Cuts metal fabrication time in half… More >>

Astro Pneumatic 600ST8 Straight Punch Flange Air Tool

• All Steel Construction is hardened and tempered
• Force is regulated by the adjustable knurled cap
• Point can be removed for regrinding
• No. 4 graduation – 8ths, 16ths, 32nds, 64ths

Product Description
These punches and nail sets are universally used, but most often by machinists and carpenters. They are well-proportioned for ease of use. The specially selected tool steel is hardened and tempered to the proper hardness. All of them feature nicely knurled finger grips for ease of handling. A special tempering process makes the head less likely to fracture from a hard, off-center blow. ALWAYS WEAR SAFETY GLASSES WHEN USING STRIKING AND STRUCK TOOLS. Rugged automatic punches have all-steel handles and parts. These punches have a mechanism that automatically strikes a blow when downward pressure is applied. No hammer is required, making one hand always free to steady the work. The adjustable knurled cap regulates the force of the blow. Should a heavy mark be required, the cap is screwed down. Progressively lighter marks are obtained by turning the cap upward. The tension of the spring, which regulates the blow is constant, so marks made by the point are un… More >>

Starrett 18A Automatic Center Punch with Adjustable Stroke

• 5″ LONG
• LIGHTWEIGHT
• HARDENED STEEL POINT
• PROVEN PUNCHING POWER

Product Description
This Window Punch is for Police, EMS or even yourself. It could save your life if you need your vehicle’s window opened fast. In a car fire or if the car goes in the water, this instrument can be used to free yourself and your loved ones. A quick tap on the window and it shatters, so you can escape…. More >>

Police & EMS Window Punch

• Diam.: 7/8″
• For punching leather, rubber, gasket, and soft metal.
• Heat treated forged steel.

Product Description
Made by General Tools. Heat treated forged steel. For punching leather, rubber, gasket, and soft metal…. More >>

General Tools 1271K 7/8-Inch Arch Punch

• Crimp And Punch Sheet Metal (Aluminum, Copper or Ductile Material)
• Crimp Width 7/8″ (22mm)
• Punch 15/64″ (6mm)
• Swivel Head
• Max. Sheet Thickness Up To 18 Gauge (0.8mm)

Product Description
*Crimp Width 7/8″ (22mm)* Punch 15/64″ (6mm)*Swivel Head*Max. Sheet Thickness Up To 18 Gauge (0.8mm)*Crimp And Punch Sheet Metal (Aluminum, Copper or Ductile Material)… More >>

Neiko Pro Tools Hand Flange Punch and Crimping Tool

• Essential metal-forming tool set used in dapping, doming, dishing or sinking sheet metal
• Produce professional metalworking results for jewelry, plating, fabrication or sculpture
• Complete set includes 24 punches 2.3-25mm, 18 die-size block and wood stand to keep organized
• Durable high-carbon steel with mirror-polished heads & block, corrosion resistant black oxide shafts
• Impressive set that will last for generations; hardwood case size-marked for quick identification

Product Description
The terms are often used interchangeably, but sinking, doming, dishing or dapping is a metalworking technique used to form spherical/semi-spherical shapes in sheet metal. Basically, the metal is hammered into one or more of the concave indentations (called ‘die’) machined on the block using one of the sphere-end punches. The technique is commonly used in jewelry making, fabrication, plating or metal sculpture. Punch sizes in millimeters: 2.3, 3.5, 4.3, 5.1, 5.9, 6.7, 7.5, 8.3, 9.1, 9.9, 10.7, 11.5, 12.3, 13, 13.8, 14.6, 15.4, 16.2, 17, 18.6, 20.2, 21.8, 23.4 and 25. Punches average 3-1/4″L; case dimensions 7-1/2″ x 4-1/2″. Total weight 7.5 lbs…. More >>

24-Piece Sinking – Doming – Dapping Punch & Die Set